- Development of the gasoline car
The pneumatic rubber tire is the point of contact between the automobile and the road surface. It functions to provide traction for acceleration and braking and limits the transmission of road vibrations to the automobile body. Inner tubes within tires were standard until the 1950s, when seals between the tire and the wheel were developed, leading to tubeless tires, now used almost universally.
Tire tread designs are tailored for the characteristics of the surface on which the vehicle is intended to operate. Deep designs provide gripping action in loose soil and snow, while smooth surfaces provide maximum contact area for applications such as racing. Current passenger car treads are a compromise between these extremes.
A typical tire casing is fabricated from layers, or plies, of varying proportions of rubber compounds reinforced with synthetic and carbon fibres or steel wire. The composition of the reinforcement and the angle of its application to the axis of the tread affect the ability of the tire to respond to sidewise forces created during cornering. They also affect harshness or vibration-transmission characteristics.
By 1990, longitudinal-, bias-, and radial-ply constructions were in use, with layers of two, four, or more plies, depending on the load capacity of the design. An additional factor relating to the load capacity of a particular construction is the pressure to which the tire is inflated. New designs also have lower height-to-width ratios to increase the road-contact area while maintaining a low standing height for the tire and consequently the car.
Motor vehicle theft has been a problem since the start of the automobile age. The 1900 Leach automobile featured a removable steering wheel that the driver could carry away to prevent unauthorized vehicle use. More recently, sophisticated electronic alarms, some of which incorporate radio beacons, and more tamper-resistant wiring and electronic locks have been produced. Through the use of wireless technology, vehicles equipped with Global Positioning System (GPS) satellite navigation systems may be tracked and recovered when stolen.
From its beginnings the automobile posed serious hazards to public safety. Vehicle speed and weight provided an impact capacity for occupants and pedestrians that produced great numbers of fatalities (13,000 in 1920 in the United States alone and many more in Europe, as well as many serious injuries). During the 20th century the rates of death and injury declined significantly in terms of vehicle miles, but, because of the increased number of vehicles on the road, total fatalities declined only slightly. During 2005–10, however, fatalities declined by 25 percent for reasons that are not understood. This downward trend continued in the following decade. Most fatal accidents occur on either city streets or secondary roads. New divided roadway designs are relatively safer. Driver training, vehicle maintenance, highway improvement, and law enforcement were identified as key areas responsible for improving safety, but the basic design of the vehicle itself and the addition of special safety features were significant factors in worldwide reduction of fatal accidents. Rates vary from country to country. Safety features of automobiles come under two distinct headings: accident avoidance and occupant protection.
Accident-avoidance systems are designed to help the driver maintain better control of the car. The dual-master-cylinder brake system is a good example. This protects the driver against sudden loss of brake line pressure. Front and rear brake lines are separated so that if one fails, the other will continue to function.
Systems for protecting occupants in the event of an accident fall into four major classes: maintenance of passenger-compartment integrity, occupant restraints, interior-impact energy-absorber systems, and exterior-impact energy absorbers. Statistics indicate a far higher chance for survival among accident victims remaining inside the passenger compartment. Passenger-compartment integrity depends significantly on the proper action of the doors, which must remain closed in the event of an accident and must be sufficiently secure to prevent intrusion. Door-latch mechanisms have been designed to resist forward, rearward, and sideward forces and incorporate two-stage catches, so that the latch may hold if the primary stage fails. Reinforcement beams in doors are designed to deflect impact forces downward to the more rigid frame structure below the door. Forces are directed through reinforced door pillars and hinges.
Occupant restraints are used to help couple the passenger to the car. They permit decelerating with the car rather than free flight into the car structure or into the air. A combination of lap and shoulder belts is the most common restraint system. The belts consist of web fabrics that are required by regulations in various countries to withstand 6,000-pound (2,700-kg) test loading and are bolted to the car underbody and roof rail. Button-type latch release mechanisms are provided for buckles.
Another line of engineering development has centred on passive restraints that do not require any action by the occupant. In particular, commercial air bags were introduced in the 1980s, and all new automobiles sold in the United States since 1998 (1999 for light trucks) have required both driver and front passenger air bags. When a vehicle equipped with an air bag undergoes a “hard” impact, roughly in excess of 10 miles (16 km) per hour, a crash sensor sends an electrical signal that triggers an explosion which generates nitrogen gas to inflate air bags located in the steering column, front dashboard, and possibly other locations. Air bags burst from their locations and inflate to a position between occupants and the car structure in less than one-tenth of a second. The inflated air bags absorb impact energy from occupants by forcing gas out through a series of ports or orifices in the air bag fabric. Air bags collapse in about one second, thereby allowing occupants to exit the vehicle.
It has been estimated that 46 percent of front-seat fatalities could be eliminated by air bags when they are used in conjunction with lap or lap-and-shoulder belts. This is a 10 percent improvement over the use of lap and shoulder belt systems alone. The front-mounted air bag does not provide protection in side or rear crashes or in prolonged impacts from rollovers. Additional side-mounted air bags, however, provide a measure of protection in side impacts and are available in some vehicle models.
Interior-impact energy-absorbing devices augment restraint systems by absorbing energy from the occupant while minimizing injuries. The energy-absorbing steering column, introduced in 1967, is a good example of such a device. Instrument panels, windshield glass, and other surfaces that may be struck by an unrestrained occupant may be designed to absorb energy in a controlled manner.
Exterior-impact energy-absorbing devices include the structural elements of the chassis and body, which may be tailored to deform in a controlled manner to decelerate the automobile more gradually and, as a result, leave less force to be experienced by the occupants. Stress risers in the form of section irregularities have been built into front frame members of some cars. These are designed to buckle under severe loads and absorb energy in the process.